Step 1 - Assess the Damage
Carpet that has been saturated in clean, sanitary water such as rainwater or tap water may be salvageable, depending on the type of carpet and how long it was wet. Water from toilets or other contaminated sourcesruin your carpet for good. Carpet saturated with water considered to be “black,” such as groundwater or sewage, is definitely not salvageable and should be replaced at once.
Step 2 - Determine the Water Source
For water that came from a single occasion, such as an overflowing bathtub or toilet, you will typically not need to be concerned about a continual flow of water onto your carpet. You do not need to take any action to stop the flow. If, however, the water that soaked your carpet continues to flow, you will need to stop it before deciding what to do with your carpet. If the flow of water is from a broken pipe, you might need to call a plumber. If the water comes from sewage or ground water, you may need the help of a contractor before you can begin cleaning or replacing your carpet.
Step 3 - Contact Your Insurance Agent
Armed with information about the extent of the damage to your carpet and the likely cause of the damage, contact your insurance company and determine with them what replacement help you can expect. Avoid investing in new carpets until you know what your insurance company is willing to do.
Step 4 - Treating a Small Carpet Area
If you have decided to proceed with repairing or replacing your damaged carpet and you have determined that the wet carpet needs to be disinfected, make a solution consisting of 1-gallon of clean water with 2-tablespoons of liquid bleach. If you have furniture sitting on the carpet, remove it so that your floor area is open. Use the solution to scrub the contaminated carpet. Use a box cutter or utility knife to cut through the carpet and padding around the contaminated area. Lift the carpet and remove the padding.
Step 5 - Dry the Soiled Carpet
Place large fans in the area of the soiled carpet, directed so that they blow air directly on the soiled carpet. Let the fans blow for 36 hours, or until the carpet is dry. If you have a dehumidifier, turn it on. Keep foot traffic off the wet carpet while it is drying. After 12 hours of drying, if you don’t see a noticeable difference in the wet condition of the carpet, you should consider replacing the it. Mold typically will begin to develop after this period of time.
Testing for Iron in Well Water
If you are testing well water, you may want to test for iron. The United States Department of Natural Resources does not list iron as a hazardous contaminant, but considers it an aesthetic contaminate in that it will give the water not only an odd taste, but also an odor and pigment that stains clothing, fixtures and dishes. Before you try to correct your water, it should be tested for hardness, pH, bacteria and iron concentration.
Step 1 - Testing Your Water
Do-it-yourself water test kits are available and can be used. Many experts believe that extensive testing must be done by professionals to get the best results. These experts also believe that professionals must be consulted to fix the problem. In many locales, you can have your water tested at a County Extension Office. If the local government cannot perform the test, they may still offer you information about water testing.
You can often tell if you have iron in your water just by observation. Soluble iron can be detected by filling a clear glass with water from your well. Let it sit a few minutes. If iron is present, you will notice tiny red particles floating to the bottom. Insoluble iron is the discolored water that you get when you turn on your faucet. It can be red, brown, or yellow. The color continues no matter how long you let the water run.
Step 2 - Removing the Iron
There are many ways to remove iron from your well. In most cases, you should consult with a professional before taking this step. It can be as simple as installing a water softener with an iron filtration system. More drastic solutions involve digging or expanding your existing well.
Well Water Problems: Why Does the Water Appear Cloudy When Initially Pumped?
Common well water problems can include the appearance of cloudy water. There are a variety of issues that could cause cloudy water. It is important to investigate the situation in order to address the problem correctly and to be certain that your well water is safe for household use. Perform these tasks to determine the source of your cloudy water.
Pump or Filter
Fill a drinking glass with well water. Allow the water to sit for a few moments. If the water comes from the tap cloudy then clears after it is allowed to settle, your pump or water filter may be experiencing problems.
Residue in the Well
The presence of dirt, silt, or rust residue in your system can cloud your well water. If these particles are in your system, they will eventually be pumped along with the water through your pipes and out of your faucet.
Excess Surface Water
Surface water that seeps into your well is usually benign; however, if there is any excess amount getting into your system, you could experience cloudy water. Large amounts of rainfall could cause excess surface water problems.
Testing and Maintenance
Ensure that your well water is safe through regular testing. Have your water privately tested for any bacterial contaminants such as E. Coli. Be sure your well water filtering system is operating properly. Replace your water filter on a regular basis.
carpet water damage cleanup, carpet water damage repair, carpet water damage sydney
Source: http://docphy.com/business-industry/business/repair-water-damaged-carpet.html
No comments:
Post a Comment